Course 007 Behavioral Modeling and Digital Predistortion of RF Power Amplifiers
Available course dates
This course has no planned course dates.
If you are interested in this course, contact us at cei@cei.se
007 Behavioral Modeling and Digital Predistortion of RF Power Amplifiers
TECHNOLOGY FOCUS
The goals of RF power amplifier design are high efficiency and linearity. With modern cellular communications modulation formats such as LTE and WCDMA these goals are difficult to achieve simultaneously with traditional RF PAs, and high-efficiency architectures such as Doherty, Envelope Tracking, and so forth are becoming more commonplace.
These PAs require an additional linearization system to achieve the mandated linearity specifications.
The emergence of high-speed digital signal processing techniques has enabled the linearization to be accomplished in the digital signal domain, and digital pre-distortion (DPD) is now the preferred linearization technique.
COURSE CONTENT
This course explains the nonlinear behavior of RF power amplifiers, developing general modeling techniques to describe the nonlinearities and memory effects. A system-level approach to the modeling and linearization of the PA is adopted, and techniques for implementation of DPD in practical situations are described.
Upon completing the course, the participant will be able to:
- Understand and describe the nonlinear behavior and memory effects found in RF power amplifiers
- Use and understand the mathematical algorithms for behavioral modeling and digital pre-distortion
- Use and implement digital pre-distortion methods for linearization of RF Pas
- Evaluate and compare modeling and DPD techniques
Mathworks MATLAB is used for all of the mathematical modeling, and Keysight ADS for any circuit simulations for verification, presented in the course. The course is intended to use these tools as a way of showing strategies and examples during the course. It is not mandatory that participants have previous knowledge of using these specific tools.
WHO SHOULD ATTEND
This course is suitable for:
- RF PA designers
- DSP designers
- System-Level engineers
who are involved in the specification, design, and implementation of linearized RF PAs and transmitter systems, or who are developing pre-distortion methods, software and algorithms for linearization of RF PAs.
Electrical Engineering degree or equivalent and at least two years applicable practical experience is recommended.
Daily Schedule
Day 1
RF Power Amplifiers in Modern Wireless Communications Systems
- Modern Wireless Communications modulations formats: LTE, WCDMA
- Signal Metrics: Peak-to-Average Power Ratio
- High-efficiency PA architectures: Doherty, Envelope Tracking
- PA metrics: AM-AM, AM-PM, ACLR, EVM
Introduction to Models and Modeling
- Compact models, Behavioral models
- Introduction to System Identification methods
Day 2
Behavioral Modeling Methods
- Linear System review
- Nonlinear modeling
- Memory effects
- Nonlinear dynamical models: Volterra Series formulations and practical implementations
- Artificial Neural Networks
- Frequency-domain models and methods: X-parameters
Day 3
Digital Pre-Distortion Methods
- Typical architectures and approaches using digital control techniques; ‘indirect learning’; LUT and algorithmic approaches
- Adaption techniques: convergence, optimization
- DPD implementations: hardware, system components, power and cost
- Practical and commercial DPD systems overview
Future Developments
- Carrier aggregation
- Wide bandwidths
- SDR
- etc
ALL COURSE DATES FOR THE CATEGORY: Circuit & System Design, RF & MW Design
026 Essentials of Radio Communications Systems
The advent of 5G and the technology spin-offs along the way have re-invigorated developments in all radio systems. They have produced new levels of sophistication as well as RF ICs for complex functions which amalgamate analogue/digital circuit ideas as well as sophisticated signalling and protocol layers.
This comprehensive course, from an established expert and IEEE life fellow, gives a thorough view of all key elements of receivers and transmitters, from circuit blocks through the system level to network concepts.
Read full course description including course schedule082 5G and Beyond Wireless Communication System Design
841 Metal, Plasma, and Metamaterial Antennas with Applications to Radar, Ordnance Mine Detection, and Cell Towers
086 RF Component and System Measurements
008 Advanced RF Power Amplifier Techniques for Modern Wireless and Microwave Systems
Location: Barcelona, Spain
Date: April 13 - April 17, 2026
Duration: 5 days
Instructors: Professsor Dr. Steve C. Cripps, Dr. Jeff Powell and Dr. Roberto Quaglia
In any system, the power amplifier is a critical component. It is typically the most costly single item and consumes most of the supply power. Knowledge of the possibilities for trading power per unit cost with efficiency and linearity often forms the basis for the entire system architecture design. This 5-day course deals with the theory and design of RF Power Amplifiers for wireless, satcom, and microwave applications and features in-depth treatment of PA design, PA modes, envelope power management, and non-linear effects.